FARU
EN
BKC-Logo-Final4

BUP 630

Home BUP 630

,

BUP 630

Unsaturated Polyester Resin

Orthophthalic Polyester Resin

Product Description:

BUP 630 is an un-promoted orthophthalic based unsaturated polyester resin with low color, medium viscosity, limited water absorption and very good mechanical properties for ambient temperature cure with MEK peroxide.

Characteristics and Advantages:

  • Low color
  • Medium viscosity
  • Limited water absorption
  • Resistance to hydrolysis
  • Impact resistant
  • Very good mechanical properties
  • Water contact/ hygienic approval

Uses:

  • Manufacturing pipes
  • Manufacturing tanks and reservoirs
  • Fabricating structural hygienic fittings
  • Hand lay-up
  • Aqua park equipment fabrication
  • Marine vessels and boats
  • Pultrusion

Technical Properties:

Physical data in liquid state at 25°C

These data are measured for each lot by our QC lab before its release.

Properties

Unit

Value

Test method

Appearance

NA

Clear

NA

Color

Gardner

Max 2

ASTM D1544

Viscosity (at 25°C)

mPa.s (cP)

450-700

ISO 2555

Density (at 23°C)

g/cm³

1.1351

ASTM D1475

Acid number

mg KOH/g

10-14

ASTM D1639

Solid content

wt %

63±2

ASTM D1259

Gel time*

min

15-35

ASTM D2471

Curing time

min

10-20

ASTM D2471

Peak exothermic temperature

℃

Max 190

ASTM D2471

Water absorption

wt %

Max 0.2

ISO 62

Flash point (open cup)

℃

22

ASTM D92

* Promoter: 0.5 g Cobalt (1%) in 100 g resin @25 °C

Initiator: 2 g MEKP (50%) in 100 g resin

Typical non-reinforced casting properties

These data are not subject to routine monitoring or part of the specifications; they are only reported for a better product description.

Properties

Unit

Value

Test method

Tensile strength

MPa

Min 60

ISO 527-2

Tensile elongation

%

3.4

ISO 527-2

Tensile modulus

MPa

1895

ISO 527-2

Flexural strength

MPa

Min 120

ISO 178

Flexural modulus

MPa

3618

ISO 178

Heat distortion temperature (HDT)

°C

Min 65

ASTM D648

Hardness (Barcol)

NA

Min 40

ASTM D2583

Linear shrinkage (∆L/L)

%

Max 1.3

ASTM D2566

Product safety and Environmental protection:

The usual protective measures employed during the handling of Unsaturated Polyester Resins should be observed. Further product safety information can be obtained from our Material Safety Data Sheet which is available on request.

 Packaging: 225 kg (net) in steel drums.

Storage: Store in a cool place below 25 °C and away from moisture and direct sunlight. Under above mentioned storage conditions, the shelf life of the resin will be at least 6 months ex-works.

Disclaimer: The information and in particular the recommendations relating to the application and use of Bonyan Kala Chemie products are given in good faith based on our current knowledge and expertise of the products when properly stored, handled and used under normal conditions within their shelf life. In practice, the differences in materials, chemistries and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any recommendations, or from any other advice offered. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users should always refer to the most recent issue of the Technical Data Sheet for the product concerned, copies of which will be supplied on request or can be accessed from www.bonyankala.com.